On this page i collect all kind of information that Douglas Edwards gave us during his special Energy-Workshop. The information is available for all on public Facebook-Pages, but it is hard to sort out the good ones.
Page 1 | 2
Douglas Edwars: The ones that will be attending class, need to start gathering some basic things….a couple start/run capacitors, at least 3 different coils(induction), transformer,(this one is tricky). You can use salvaged transformers until you have an understanding of how to create your own. Some 12 or 14g insulated wire, different size relays,(auto relays work well for smaller applications). There are a couple more odds and ends, but these are the main items needed in order to create your own generator.
A relay is an electrically operated switch. Many relays use an electromagnet to mechanically operate a switch, but other operating principles are also used, such as solid-state relays. Relays are used where it is necessary to control a circuit by a separate low-power signal, or where several circuits must be controlled by one signal. The first relays were used in long distance telegraph circuits as amplifiers: they repeated the signal coming in from one circuit and re-transmitted it on another circuit. Relays were used extensively in telephone exchanges and early computers to perform logical operations.
These allow for a smaller wire to open the circuit of a much larger wire, as seen on most auto’s used in the “starting circuit”.
Question: Should the relays be a minimum voltage?
Voltage is not important at this point, as we will be using them to have a better understanding of how to build our own..Coils/winding’s are important to better understand, as many have looked over these simple devices..Yes, single pole will work, but so will any other. I only used auto as an example, because many are more familiar with auto relays.
The influence of magnetic fields on the behavior of plasmas is dramatically illustrated by the coronal loop structure shown in this image acquired with the SOHO Extreme-ultraviolet Imaging Telescope (EIT). Magnetic field lines emerging from the photosphere (the Sun’s visible “surface”) and returning to it in a region of opposite magnetic polarity organize the hot (one million degree Kelvin) plasma of the corona into this loop structure on the Sun’s eastern limb. This false-color image shows extreme ultraviolet emissions (195 angstroms) from highly ionized iron atoms (Fe XII) in the solar corona.
(Image courtesy of SOHO/EIT. SOHO is a project of international collaboration between ESA and NASA. More EIT images can be accessed at the SOHO Image Gallery.)
The sun is a very important object of interest when learning about Plasma, as they are one in the same.
Today, we will discuss Capacitors, in combination with a relay What they do, and why they are needed..There are a couple of things going on when we apply these two together.. I will be willing to say, that not too many were even aware that my device had at least 3 relay’s..
In a way, a capacitor is a little like a battery. Although they work in completely different ways, capacitors and batteries both store electrical energy. A capacitor is a passive two-terminal electrical component that stores potential energy in an electric field. The effect of a capacitor is known as capacitance. While some capacitance exists between any two electrical conductors in proximity in a circuit, a capacitor is a component designed to add capacitance to a circuit. The capacitor was originally known as a condenser.
A motor capacitor, such as a start capacitor or run capacitor (including a dual run capacitor) is an electrical capacitor that alters the current to one or more windings of a single phase AC induction motor to create a rotating magnetic field.
Can we all see the difference? Alters the current to 1 or more windings,(coils), of single phase AC… Very important to note..
Timing is a very critical part to this or any other circuit… Happy Hunting.. Think Analog, now think Digital
Question: think that the interesting part happens between the switch. when the potential goes quickly from A to B this is the time where we should ‘kick in with something’
Now everyone is starting to think, instead of allowing others to do this for them… You are on the right track…
Question: I think the secret device of Douglas Edwards is bucking coils with a spark gap inside or outside. If not it is 95% similar working device made from 2×2 coils in bucking mode and a transformer to convert exess energy to usable power.
No spark gap… more coils.. Not bucking..
When we look at the fields present when sending a potential through a coil, we get both, the positive, and the Negative. We use the positive for source, and we use the Negative for ground reference.. What if we captured the negative field and forced it back into the primary potential???
We capture the field effect with another coil.
Question: in my understanding if we have two different potentials it cannot be done to feed one by another because if we do that we have no more difference between two points. maybe we need a third reference point to manage something.
you need to lurk moar…lol Your understanding is wrong my friend, we do not use 2 different potentials, we use the same, we just send it back to the primary…
Question: what i dont get is, that if i am able to force the nagative energy into positive it must be of a higher potential. but how could this be? the negative energy has to convert onto the positive side and there must be a kind of amplification.
Whenever you energize a coil, you get the 2 fields present, one has to be fed back into another primary.
Question: ok so if i have a single coil and i energize this on one end (entrance point) the energy level builds up till it reaches the other end (exit point). between entrance and exit i have a potential difference which comes from one source.
when u energize the coil, you get the opposite that you put in for free we will say. Take this “free’ field, and send to another primary. This is the start.
Question: hello douglas! do you think that it is a good idea to take the power from the plug, or is it better to produce a ‘signal’ for ourselves. the problem with AC is, that you always need a lot of current to bring things in operation. there are other ‘forms of signals’ that can handle energy-transfer much better. would you agree on that my friend have a nice day!
No, you can create your own power… Current the way it is designed to be used right now, yes. Current the way it is suppose to be used, No! ALL signals can be made into a source voltage…
actually current = heat
Question: Maybe we should use the atmosphere to gain potential and the earth will deliver all the current that is needed for operation. would you agree?
Now your thinking in terms of “free energy”, so how do we harness this potential, that we KNOW is there? Then “transform” it into a usable current? Since minimal voltage is present, we will first need to “multiply” the source voltage. This is where capacitors and diodes come into play again…
Question: so the the primary winding of the transformer is feeded by grounding and a copper antenna?
No. The copper antennae is correct, but can also be aluminum/copper mix.. , but is only the capstone.
Question: sry for stupid questions, so when i think in fieldflow it has to be grounded in it self?so in matterstate this woud be grounding on the ironcore of the transformer.?
in the above statement, the earth itself would act as ground.
Question: think that the difficult part is the current. potential from antenna can be duplicated thats not the challenge..
current isn’t either, you have just been asleep for centuries… It will come, and when it does, the floodgates will open…What is current? and not the BS in the books. What is it simply?
Question: hmm.. light maybe. or a special frequency.. earth is a big mass. and where the mass is are a lot of electrons
Vibration…yes. I gave you this one as you were so close…lol
Question: In the past weeks i did a couple of tests with piezzo elements which i put in water to see the reaction when special frequencies plays directly in the liquid. and it is amazing when you get ‘the right frequency’ to watch the reaction of water. the surface of water is shaking and the sound volume is amplified much too. played with frequencies from 200 to 20000. my problem is, that the piezzo elements did the job for only 15 minutes because they dissolve. and there is something very special going on between 19.500 and 20.000 Hz. between this range many ‘bubbles’ appear on the metal which did not come to the upper surface. the ‘air-bubble’ is attracted by the metal plate of the piezzo and grows in size rapidly. i cannot watch this process to the end because the piezzo element destroys itself after a few seconds on this frequency. actually i have no idea what is going on in the water but i like to do more tests. i am looking for a way how i can transfer soundwaves into water but have no idea how i can do this. if you have any idea please feel free to comment. thx
Very nice… Now then find a container of two opposing elements, and place water inside, resonate until separation/division occurs, collect Hydrogen, pass through very Strong Magnetic field, another way to ignite plasma if you will…… Be careful!!
this device uses a 9vDC battery and It will produce 300AC volts…
air core, 5 pin relay 12v, 5v 100uF, AC 10uF, 250v
Question: how does the air core wind, does is wind as secondary and primary
no, just a primary…
Question: How many windings do we need for the coil?
around 300 stay within the multiples of 3,6, or 9..
Marc is a very intelligent researcher/engineer.. I have a few other schematics I will share, that were shared with me.. As you will note, we have permission to use this in our group, but you cannot sell his device under your own name, you can share it, but not profit from it… Beautiful!! Peace and love to you all.